Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
5. Transmission
6. A running gear
7. A steering
8. Brake system
8.1. Features of the device
8.2. A good advice
8.3. Check and adjustment of brake system
8.4. Replacement of a brake liquid
8.5. Prorolling of a hydrodrive of brake system
8.6. The main brake cylinder
8.7. The vacuum amplifier of brakes
8.8. A pressure regulator
8.9. Replacement of hoses and pipelines of a hydrodrive of brakes
8.10. Brake mechanisms of forward wheels
8.11. Brake mechanisms of back wheels
8.12. A lay brake
8.13. Removal and dismantling of pedal knot
8.14. Possible malfunctions of brake system, their reason and ways of elimination
9. An electric equipment
10. A body
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 













8-12-stoyanochnyjj-tormoz.html

8.12. A lay brake

Features of a design
The lay brake system with a mechanical drive operates on brake mechanisms of back wheels.

Fig. 8.9. Details of a drive of a lay brake: 1 – the lever; 2 – the button; 3 – a draught spring; 4 – draught of a latch; 5 – a cover; 6 – a forward cable; 7 – directing a back cable; 8 – распорная the plug; 9 – оттяжная a spring; 10 – распорная a lath; 11 – the lever of a manual drive колодок; 12 – a back cable


The lay brake has a mechanical drive from the lever 1 (fig. 8.9). Through a groove directing 7 there passes an average part of the back cable which tension regulate a nut screwed on a carving tip of a forward cable. Between directing 7 and an adjusting nut the plug 8 is established распорная.
On the back ends of a cable there are tips, each of which is connected to a hook of the lever 11 manual drives колодок. This lever шарнирно is attached by a finger to brake колодке and the top part rests against a groove распорной laths 10. In an opposite groove of a lath the edge brake pad is established.

Replacement of a back cable of a lay brake
Back cable replace at excessive вытягивании (impossibility of adjustment of a lay brake), mechanical damages and mobility loss to a cover.
It be required to you: keys «on 8», «on 13» (two), pincers of type "cobra", пассатижи.
1. Remove a brake drum (Removal and installation of a brake drum »see«).
2. Ослабьте a counternut inhaling on a tip of a forward cable.
3. Keeping a tip from проворачивания pincers, turn on till the end of a tip a counternut and an adjusting nut.
4. Remove a spring.
5. Keeping a tip from проворачивания, remove from a tip a counternut, an adjusting nut and распорную the plug.
6. Remove from a tip directing and disconnect it from a cable.
7. Deduce a cable from an arm of a beam of the back bridge and...
8.... From an aperture of an arm of a body.
9. Turn out two bolts of fastening of the holder of a cover of a cable to a brake board.
10. Disconnect a tip of a cable of a drive of a lay brake from the drive lever.
11. Extend a cable from an aperture of a brake board.
12. Similarly remove the right branch of a cable and remove a back cable from the car.
13. Establish on the car a new cable in an order, the return to removal.
14. Adjust lay brake system (Check and adjustment of a lay brake »see«).

Replacement of the lever and forward cable of a lay brake
The lever in gathering replace at deterioration or damage of gear sector or the doggie.
Forward cable replace at excessive вытягивании (impossibility of adjustment of a lay brake) or mechanical damages.
It be required to you: a key «on 13», пассатижи, a screw-driver.
1. Disconnect a back cable with directing from a tip of a forward cable («Replacement of a back cable of a lay brake» see).
2. Remove facing of a tunnel of a floor (Removal and installation of facing of a tunnel of a floor »see«).
3. Turn out two bolts of fastening of an arm of the lever to a floor and remove the lever.
4. Remove a lock ring of an axis of the lever.
5. Take out a lever axis.
6. Extend a cable in salon.
7. Establish a new cable and the lever in an order, the return to removal.
8. Adjust lay brake system (Check and adjustment of a lay brake »see«).

«The previous page
8.11. Brake mechanisms of back wheels
The following page»
8.13. Removal and dismantling of pedal knot