Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
5. Transmission
6. A running gear
7. A steering
7.1. Features of a design
7.2. Survey and steering check on the car
7.3. Check of a tension and adjustment of a belt of a drive of the pump of the hydraulic booster
7.4. Liquid replacement in hydrosystem of the amplifier of a steering
7.5. Replacement of a tank of hydrosystem of the amplifier of a steering
7.6. Prorolling of system of the hydraulic booster of a steering
7.7. Backlash adjustment in gearing of a roller with a worm
7.8. Removal and steering wheel installation
7.9. Replacement of shaft of a steering
7.10. Replacement of steering draughts
7.11. Removal and installation of the steering mechanism
7.12. Removal and installation of the pump of the hydraulic booster
7.13. Removal and installation of the pendular lever
7.14. Dismantling, дефектовка and assemblage of the pendular lever
7.15. Possible malfunctions of a steering without the hydraulic booster, their reasons and ways of elimination
7.16. Possible malfunctions of the hydraulic booster of a steering, their reason and ways of elimination
8. Brake system
9. An electric equipment
10. A body
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 











7-10-zamena-rulevykh-tyag.html

7.10. Replacement of steering draughts

It is necessary to replace pognutye steering draughts necessarily as editing of this responsible element of a steering is inadmissible because in a draught material there can be cracks.

Replacement of lateral draughts
It be required to you: a key «on 22», a stripper for выпрессовки a finger of the spherical hinge, пассатижи.

       NOTES
Work is more convenient for carrying out on the lift. It is possible to execute it and on the car established on support.
Draught replacement is shown on an example of the left lateral draught, right replace similarly.

1. Remove a corresponding wheel.
2. Расшплинтуйте a nut of a finger of the external hinge.
3. Turn away a nut.
4. Establish a stripper and выпрессуйте a finger of the spherical hinge from the rotary lever.

       GOOD ADVICE
In the absence of a stripper the finger of the spherical hinge can be beaten out sharp blows of a hammer on an end face of a lug of the rotary lever, putting blows along a lever axis.

5. Расшплинтуйте a nut of a finger of the internal hinge also turn away a nut.
6. Establish a stripper and выпрессуйте a finger of the spherical hinge from сошки the steering mechanism.
7. Remove steering draught.
8. Establish new steering draught in an order, the return to removal.

       GOOD ADVICE
As far as possible not to break corners of installation of wheels, measure distance centre to centre hinges of old draught and, having weakened coupling bolts adjusting муфты new draught, establish the same distance centre to centre its hinges. Do not forget to tighten after draught installation a nut of coupling bolts муфты.

9. Check up and in case of need adjust corners of installation of wheels at servicing deport.

Replacement of average draught
It be required to you: a key «on 22», a stripper for выпрессовки a finger of the spherical hinge, пассатижи.

       NOTES
Work is more convenient for carrying out on the lift. It is possible to execute it and on the car established on support.
Replacement of average draught is shown on an example of a detachment of the spherical hinge from сошки the steering mechanism. Disconnect draught from the pendular lever similarly.

1. Remove a corresponding wheel.
2. Выпрессуйте a finger of the spherical hinge of lateral draught from сошки the steering mechanism («Replacement of lateral draughts» see) and take lateral draught aside.
3. To removal of cross-section draught disturbs картер a reducer of the forward bridge (fingers of spherical hinges of draught do not manage to be deduced completely from eyes сошки and the pendular lever). Therefore disconnect from the stabilizer a reducer of the forward bridge for what turn away four nuts of fastening скоб stabilizer fastenings to картеру a reducer. Under a body weight the reducer will be turned on forward support, and between it and draught the backlash, sufficient for draught removal will open.
4. Расшплинтуйте a nut of fastening of a finger of the spherical hinge of average bent for сошке the steering mechanism...
5.... Also turn away a nut.
6. Establish a stripper and выпрессуйте a finger of the spherical hinge from a lug сошки the steering mechanism.
7. Remove steering draught.
8. Establish new steering draught and other removed knots in an order, the return to removal.

«The previous page
7.9. Replacement of shaft of a steering
The following page»
7.11. Removal and installation of the steering mechanism