Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
5. Transmission
6. A running gear
7. A steering
7.1. Features of a design
7.2. Survey and steering check on the car
7.3. Check of a tension and adjustment of a belt of a drive of the pump of the hydraulic booster
7.4. Liquid replacement in hydrosystem of the amplifier of a steering
7.5. Replacement of a tank of hydrosystem of the amplifier of a steering
7.6. Prorolling of system of the hydraulic booster of a steering
7.7. Backlash adjustment in gearing of a roller with a worm
7.8. Removal and steering wheel installation
7.9. Replacement of shaft of a steering
7.10. Replacement of steering draughts
7.11. Removal and installation of the steering mechanism
7.12. Removal and installation of the pump of the hydraulic booster
7.13. Removal and installation of the pendular lever
7.14. Dismantling, дефектовка and assemblage of the pendular lever
7.15. Possible malfunctions of a steering without the hydraulic booster, their reasons and ways of elimination
7.16. Possible malfunctions of the hydraulic booster of a steering, their reason and ways of elimination
8. Brake system
9. An electric equipment
10. A body
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 











7-11-snyatie-i-ustanovka-rulevogo-mekhanizma.html

7.11. Removal and installation of the steering mechanism

The steering mechanism remove for repair (it is recommended to repair the mechanism in a specialised workshop) or replacement.
The steering mechanism is established on the left longeron from its inside and fixed on a longeron of a body by three bolts inserted from the inside.
It be required to you: keys «on 17», «on 19», a screw-driver.
1. Merge a liquid from hydraulic booster system (liquid Replacement in hydrosystem of the amplifier of a steering »see«).
2. Disconnect steering draughts from сошки the steering mechanism («Replacement of steering draughts» see).
3. Turn out a bolt-union of a hose of a high pressure.
4. Pay attention to a condition of copper linings. Погнутые or strongly pressed out linings replace.
5. Ослабьте a collar of a taking away hose and...
6.... Remove a hose from the union of the steering mechanism.
7. Mark position карданного the hinge of an intermediate shaft concerning a shaft of a worm of the steering mechanism, turn away a nut of a coupling bolt and disconnect propeller the hinge of an intermediate shaft from a shaft of a worm of the mechanism of a steering («Replacement of an intermediate shaft» see).
8. Turn away three nuts of bolts of fastening of the mechanism of a steering to a longeron.

THE NOTE
Pay attention: under nuts flat washers are established. Do not forget to establish them at return assemblage

9. Take out bolts and remove the steering mechanism.
10. Establish the steering mechanism in an order, the return to removal.

Fig. 7.4. Installation of the steering mechanism on the car: 1 – bolts of fastening of the steering mechanism; 2 – the steering mechanism; 3 – сошка; Х – control distance from the centre of the bottom aperture сошки to a basic surface of the steering mechanism at
Average position сошки; and – a control corner


11. Before tightening nuts of bolts 1 (fig. 7.4), the special device сориентируйте the steering mechanism so that a corner а=28 °.
12. After installation fill the mechanism with a liquid and pump over system («Prorolling of system of the hydraulic booster of a steering» see).

«The previous page
7.10. Replacement of steering draughts
The following page»
7.12. Removal and installation of the pump of the hydraulic booster