Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
5. Transmission
6. A running gear
7. A steering
8. Brake system
9. An electric equipment
10. A body
10.1. Features of a design
10.2. Removal and installation of lobbies Lockers
10.3. Removal and installation of forward wings
10.4. Removal and installation of decorative overlays on forward wings and doors
10.5. Replacement of buffers
10.6. Removal and installation of facing of a radiator
10.7. Removal and cowl installation
10.8. Removal, installation and adjustment of the lock and a drive of the lock of a cowl
10.9. A back door
10.10. Forward doors
10.11. Back doors
10.12. Removal and installation of a cover of the hatch of a fuel tank
10.13. Seats
10.14. Removal of upholsteries of salon
10.15. Replacement of seat belts
10.16. Mirrors
10.17. Replacement противосолнечных peaks
10.18. Replacement of hand-rail
10.19. Removal and installation of facing of a tunnel of a floor
10.20. Removal and installation of the panel of fastening of a radio receiver
10.21. Removal and installation of the panel of devices
10.22. A heater
10.23. Replacement of a windscreen and glasses of a door of a back and боковины
10.24. Care of a body
10.25. Anticorrosive protection of a body
10.26. Possible malfunctions of a body, their reason and ways of elimination
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 







İòî íàäî çíàòü: https://remstroy31.ru/proshedshego.html




10-11-zadnie-dveri.html

10.11. Back doors

Removal of an upholstery of a back door
Screw-drivers with a flat and crosswise edge be required to you.
1. Having hooked a screw-driver...
2.... Remove a handle clamp стеклоподъемника, and then...
3.... The handle.
4. Pull the internal handle of the lock and turn out the screw of fastening of facing of the handle.
5. Shift back and remove handle facing (the handle remains on a door).
6. Turn out screws in a niche of an armrest and...
7.... In the bottom part of a door.
8. Hook an upholstery a screw-driver in the locations of percussion caps and...
9.... Remove it, having passed through an aperture in an upholstery the button of blocking of the lock of a door.

       GOOD ADVICE
Not to scratch the painted surfaces of a door, wind a screw-driver edge изоляционной with a tape.

10. Remove percussion caps of fastening of an upholstery if they remained at doors. The broken percussion caps replace.
11. Establish an upholstery of a door and the removed details in an order, the return to removal.

Removal and installation of the lock of a back door
It be required to you: a key «on 8», круглогубцы, screw-drivers with a flat and crosswise edge.
1. Disconnect a wire from the plug "minus" of the storage battery.
2. Remove a door upholstery («Removal of an upholstery of a back door» see).

3. Disconnect draughts from the lock.
4. Turn away a nut and...
5.... Turn out a bolt of fastening of the external handle.
6. Pull the handle on itself, take away to the left and...
7.... Remove it.

THE NOTE
Deformation (bend) of this lever often is at the bottom of failure of the external handle of a door.
If the lever is bent, accurately will correct its screw-driver.

8. Turn out screws of fastening of the lock.
9. Separate колодку a plait of wires.
10. Turn out screws of fastening and...
11.... Remove the case of a drive of blocking of the lock.
12. Disconnect draught from the internal handle.
13. Take draughts from the directing.
14. Turn out a bolt of fastening and...
15.... Remove directing опускного glasses.
16. Disconnect колодку wires from a motor-reducer of the lock and...
17.... Remove the lock in gathering.
18. Clear and examine details, grease with greasing ФИОЛ-1 or similar.
19. Will put the lock and all removed details in an order, the return to removal.

Replacement of the terminator of opening of a back door
It be required to you: keys «on 10», «on 13», a screw-driver.
1. Remove a door upholstery («Removal of an upholstery of a back door» see).
2. Replace the terminator to similarly replacement of the terminator of a forward door («Replacement of the terminator of opening of a forward door» see).
3. Establish a door upholstery in an order, the return to removal.

Replacement опускного glasses of a back door
It be required to you: keys «on 8», screw-drivers with a flat and crosswise edge.
1. Remove a door upholstery («Removal of an upholstery of a back door» see).
2. Remove стеклоподъемник (mechanism Replacement стеклоподъемника a back door »see«).
3. Turn out a bolt of fastening directing опускного glasses and...
4.... Remove the directing.
5. Remove bottom and...
6.... Top уплотнители glasses.

       THE NOTE
Уплотнители are kept on the places only at the expense of a tightness in grooves and in any way in addition are not fixed.

7. Turning glass in a window aperture, as is shown in a photo...
8.... Take it from an aperture.
9. Establish опускное glass and all removed details in an order, the return to removal.

Mechanism replacement стеклоподъемника a back door
It be required to you: keys «on 8», screw-drivers with a flat and crosswise edge.
1. Remove a door upholstery («Removal of an upholstery of a back door» see).
2. Disconnect draughts of the internal handle and lock blocking (Removal and installation of the lock of a back door »see«).
3. Fix glass in the lifted position (for example, by means of a screw-driver).
4. Turn out bolts of a plate of fastening опускного glasses.
5. Turn on two central...
6.... Top and...
7.... Bottom fastening nuts стеклоподъемника.
8. Remove стеклоподъемник in gathering through a technological window in the door amplifier.
9. Clear and examine details, grease with greasing Litol-24 or similar.
10. Establish стеклоподъемник and all removed details in an order, the return to removal.

Removal and installation of a back door
It be required to you: keys «on 13», круглогубцы.
1. Disconnect a wire from the plug "minus" of the storage battery.
2. Turn out a bolt of fastening of the terminator of opening of a door to a body («Replacement of the terminator of opening of a back door» see).
3. Take a rubber protective tube of wires from the central rack.
4. Undertaken wires, extend a socket of wires from a rack and separate it.
5. Remove lock скобы axes of loops and remove a door the same as removed a forward door (Removal and installation of a forward door »see«).
6. Establish a back door and all removed details in an order, the return to removal.

«The previous page
10.10. Forward doors
The following page»
10.12. Removal and installation of a cover of the hatch of a fuel tank