Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
5. Transmission
6. A running gear
7. A steering
8. Brake system
9. An electric equipment
10. A body
10.1. Features of a design
10.2. Removal and installation of lobbies Lockers
10.3. Removal and installation of forward wings
10.4. Removal and installation of decorative overlays on forward wings and doors
10.5. Replacement of buffers
10.6. Removal and installation of facing of a radiator
10.7. Removal and cowl installation
10.8. Removal, installation and adjustment of the lock and a drive of the lock of a cowl
10.9. A back door
10.10. Forward doors
10.11. Back doors
10.12. Removal and installation of a cover of the hatch of a fuel tank
10.13. Seats
10.14. Removal of upholsteries of salon
10.15. Replacement of seat belts
10.16. Mirrors
10.17. Replacement противосолнечных peaks
10.18. Replacement of hand-rail
10.19. Removal and installation of facing of a tunnel of a floor
10.20. Removal and installation of the panel of fastening of a radio receiver
10.21. Removal and installation of the panel of devices
10.22. A heater
10.23. Replacement of a windscreen and glasses of a door of a back and боковины
10.24. Care of a body
10.25. Anticorrosive protection of a body
10.26. Possible malfunctions of a body, their reason and ways of elimination
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 







Клининговые услуги в самаре подробнее.
Генеральная уборка по материалам www.bum.com.kz.








10-22-otopitel.html

10.22. A heater

Features of a design

Fig. 10.2. System of heating of salon of a body: 1 – a ventilation air line; 2 – an air line of heating of a windscreen; 3 – the intermediate case; 4 – an intermediate air line; 5 – the case of the filter of an air inlet; 6 – the fan of system of heating; 7 – the central nozzle of ventilation of salon; 8 – facing of the panel of control levers; 9 – a forward air line of heating of salon; 10 – a back air line of heating of salon; 11 – an air line of heating of feet; 12 – a heater in gathering; 13 – a lateral nozzle


Fig. 10.3. Heater details: 1 – a heater radiator; 2 – the left casing of a heater; 3 – a control lever заслонкой a heater; 4 – the intermediate lever; 5 – the screw; 6 – sector of levers; 7 – the drive lever заслонки air distributor; 8 – заслонка managements of a heater; 9 – heater hoses; 10 – a collar; 11 – the screen of hoses; 12 – an arm; 13 – заслонка air distributor; 14 – a sealant; 15 – the right casing of a heater; 16 – an air line of heating of feet of the passenger; 17 – a radiator lining


On the car the heater 12 (fig. 10.2) the liquid type, united with system of cooling of the engine is established. The radiator of a heater 1 (fig. 10.3) is placed in the plastic casing established in the central part of the panel of devices. Feature of a heater is absence of the crane. The heater заслонками 8 and 13 copes.

Removal and heater installation  
Screw-drivers with a flat and crosswise edge be required to you.
1. Disconnect a wire from the plug "minus" of the storage battery.
2. Remove the panel of devices (Removal and installation of the panel of devices see).
3. Having pulled on itself, remove the handle of management of a heater...
4.... The management handle рециркуляцией and...
5.... Facing of the panel of control levers by a heater.
6. Turn out screws of fastening of an arm of control levers a heater.
7. Take lamps of illumination of the panel of levers.
8. Separate колодку a plait of wires.
9. Turn out screws скоб fastenings of draughts.
10. Disconnect draughts from levers заслонок a heater.
11. Turn out the screw скобы fastenings of draught of a drive заслонки рециркуляции and...
12.... Disconnect draught.
13. Take an arm of levers and disconnect колодку a plait of wires from the switch of the electrofan of a heater.
14. Turn out screws скоб fastenings of draughts and disconnect draughts.
15. Remove the switch of the electrofan of a heater (Removal and box installation воздухопритока, flexible draughts and an arm of levers of a drive of a heater see).
16. Turn out screws of fastening of a heater to a cross-beam of the panel of devices and...
17.... Remove a heater.
18. Establish a heater and all removed details in an order, the return to removal.

Replacement of a radiator of a heater
If from a heater the cooling liquid leaks, means, негерметичен and it it is necessary to replace a radiator.

       GOOD ADVICE
Never tighten with elimination of a leak of a cooling liquid in car salon as its evaporations are harmful to your health.

The screw-driver is required to you.
1. Remove a ware box (Removal and installation of facing of a tunnel of a floor see).
2. Remove a facing overlay of a windscreen (Removal, installation and repair of a screen wiper of a wind window see).
3. Merge a liquid from system of cooling of the engine (Replacement of a cooling liquid see).
4. Remove the filter of giving of external air and...
5.... Turn out screws of fastening of the case of the filter.
6. Turn out screws of fastening of the case of the electrofan.
7. Turn out screws of an arm of fastening of a heater.
8. Remove an air line of heating of feet of the passenger.
9. Unbend an arm of a heater and...
10.... Take an intermediate air line.
11. Turn out screws of fastening of a radiator of a heater.
12. Ослабьте collars on bringing and taking away hoses of a radiator also remove hoses.
13. Take a radiator of a heater from a casing.
14. Establish a radiator of a heater and all removed details in an order, the return to removal.
15. Fill in a liquid in system of cooling of the engine.

Removal and box installation воздухопритока, flexible draughts and an arm of levers of a drive of a heater
The screw-driver is required to you.
1. Disconnect the plug "minus" from the storage battery.
2. Remove the panel of devices together with a heater (Removal and installation of the panel of devices see).
3. Separate колодку a plait of wires of the electrofan of a heater.
4. Turn out two screws...
5.... Box fastenings воздухопритока and...
6.... Remove a box in gathering with the electrofan.
7. Remove facing of the panel of control levers by a heater (Removal and heater installation see).
8. Turn out screws скоб fastenings of draughts and...
9.... Disconnect draughts.
10. Turn out the screw скобы fastenings of draught of a drive заслонки рециркуляции and...
11.... Disconnect draught.
12. Take an arm of levers and disconnect колодку a plait of wires from the switch of the electrofan of a heater.
13. Turn out screws скоб fastenings of draughts and disconnect draughts.
14. Turn away a plastic nut of fastening of the switch of the electrofan of a heater and...
15.... Remove the switch.
16. Establish all removed details in an order, the return to removal.

The previous page
10.21. Removal and installation of the panel of devices
The following page
10.23. Replacement of a windscreen and glasses of a door of a back and боковины