10-9-dver-zadka.html
10.9. A back door Removal of an arm of a spare wheel
The key «on 17» is required to you.
|
1. Remove from an arm a spare wheel.
|
|
|
2. Turn away four nuts of fastening of an arm to a door of a back and...
|
|
|
|
|
3.... Remove the washers established under nuts.
|
4. Remove an arm and rubber washers from hairpins of a door of a back.
|
|
5. Establish an arm of a spare wheel in an order, the return to removal.
|
Removal and installation of an upholstery of a door of a back
Screw-drivers with a flat and crosswise edge be required to you.
|
|
|
|
2. Turn out the top screws of fastening of a framework of glass.
|
3. Remove from both parties of a framework decorative заглушки and...
|
|
|
|
|
4.... Turn out located under заглушками screws.
|
5. Remove a glass framework.
|
|
|
|
|
6. Turn away a jellied stopper and...
|
7.... Remove an overlay of a mouth of a tank of a washer of glass of a door of a back.
|
|
|
|
8. Accurately hook an upholstery a screw-driver in the locations of percussion caps of fastening and remove it.
|
|
GOOD ADVICE
Not to scratch a screw-driver the painted details, wind a screw-driver sting изоляционной with a tape.
|
|
9. Establish an upholstery and a glass framework in an order, the return to removal. The broken percussion caps of fastening of an upholstery replace new.
|
Removal and installation of a drive of the lock of a door of a back
Screw-drivers with a flat and crosswise edge be required to you.
1. Remove an upholstery of a door of a back (Removal and installation of an upholstery of a door of a back »see«).
|
|
2. Disconnect a wire from the plug "minus" of the storage battery.
|
|
|
|
|
3. Turn out screws and...
|
4.... Remove a motor-reducer of a drive of the lock.
|
|
5. Disconnect from a motor-reducer колодку a plait of wires
|
|
6. Establish a motor-reducer of a drive of the lock and the removed details in an order, the return to removal.
|
Removal and installation of the lock and the handle of the lock of a door of a back
It be required to you: keys «on 8», «on 10», screw-drivers with a flat and crosswise edge.
1. Remove an upholstery of a door of a back (Removal and installation of an upholstery of a door of a back »see«).
|
|
2. Disconnect a wire from the plug "minus" of the storage battery.
|
|
|
|
|
3. Turn out screws of fastening of the lock.
|
4. By means of a screw-driver disconnect draughts from the lever of the switch of the lock of a door and...
|
|
|
5.... From the door handle.
|
|
|
|
|
6. Separate black and...
|
7.... White pad plaits of wires.
|
|
8. Remove the lock in gathering with a drive motor-reducer.
|
|
|
9. Turn away a nut of fastening of the handle of a door and...
|
|
|
|
|
10.... Turn out a bolt of an arm of the handle.
|
11. In position "openly" shift the handle to the left and...
|
|
|
12.... Take the handle from a door aperture.
|
13. Put the lock of a door of a back and its handle in an order, the return to removal.
|
|
GOOD ADVICE
Before assemblage grease rubbing metal details of the mechanism of the lock консистентной with greasing.
|
It be required to you: keys «on 10», «on 13», «on 17», a screw-driver.
|
1. Disconnect a wire from the plug "minus" of the storage battery.
|
|
|
|
|
2. Turn out screws and...
|
3.... Remove percussion caps of fastening of the left upholstery of a luggage carrier.
|
|
|
|
|
4. Take an upholstery aside.
|
5. Turn out screws of fastening of an overlay боковины.
|
|
|
|
|
6. Remove a decorative overlay of an eye of a seat belt and...
|
7.... Turn out a bolt of fastening of an eye to a body.
|
|
|
|
|
8. Deduce a belt from under an overlay боковины and...
|
9.... Remove an overlay.
|
|
|
|
|
10. Disconnect колодку a plait of wires from a lamp of illumination of a luggage carrier and...
|
11.... Separate колодку a plait of wires of a door of a back.
|
|
|
|
|
12. Remove дефлектор exhaust ventilation.
|
13. Turn away a nut of fastening of the plug of a "mass" wire.
|
|
|
|
|
14. Take from a body aperture the rubber plug and...
|
15.... Take from an aperture of a body a plait of wires of a door of a back.
|
|
|
16. Turn out bolts of fastening of the terminator of opening of a door.
|
|
|
|
|
17. Turn out bolts of fastening bottom and...
|
18.... Top loops of a door of a back, preliminary having marked position of loops on a body (if will establish a former door), and...
|
20. Establish a door of a back and all removed details in an order, the return to removal.
|
|
THE NOTE
Former door establish on the labels put before removal. If establish a new door, adjust its position in a body aperture («Adjustment of position of a door of a back» see).
|
Regulate position of a door of a back by change of position of a clamp of the lock and a nest of a thorn of a door. The shock screw-driver is required to you.
|
|
1. By means of a shock screw-driver ослабьте screws of fastening of a clamp of the lock of a door and...
|
|
3. Move a clamp and a nest in a demanded direction and tighten screws.
|
Removal and installation of the terminator of opening of a door of a back
It be required to you: a key «on 13», a screw-driver with a crosswise edge, a hammer.
1. Remove an upholstery of a door of a back (Removal and installation of an upholstery of a door of a back »see«).
|
|
|
|
|
2. Turn out bolts of fastening of the terminator to a body.
|
3. Turn out screws of fastening of a tank of a washer of glass of a door of a back and remove it.
|
|
|
4. Turn out bolts of fastening of the terminator to a door and...
|
|
|
|
|
5.... Remove the terminator.
|
6. Establish the terminator in an order, the return to removal. If necessary take advantage of a hammer.
|
|
|