Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
4.1. Features of a design
4.2. A good advice
4.3. Removal and installation of a decorative casing of the engine
4.4. Removal and installation of protection oil crankcase and an engine mudguard
4.5. Replacement of a cooling liquid
4.6. Oil replacement in the engine and the oil filter
4.7. Clearing of system of ventilation crankcase
4.8. Replacement of support of a suspension bracket of the power unit
4.9. Installation of the piston of the fourth cylinder in position ВМТ of a step of compression
4.10. Check and installation of phases timing on labels
4.11. Replacement натяжителя chains of a drive of a camshaft
4.12. Replacement успокоителя chains of a drive of a camshaft
4.13. Boot replacement натяжителя chains of a drive of a camshaft
4.14. Replacement of a chain of a drive of a camshaft
4.15. Replacement of hydrosupport of levers of a drive of valves
4.16. Removal, installation and дефектовка a flywheel
4.17. Replacement of the forward bearing of a primary shaft of a transmission
4.18. Replacement of details of consolidation of the engine
4.19. Camshaft replacement
4.20. A head of the block of cylinders
4.21. Removal and engine installation
4.22. Engine repair
4.23. Greasing system
4.24. Cooling system
4.25. System of release of the fulfilled gases
4.26. The power supply system
4.27. Possible malfunctions of the engine, their reason and ways of elimination
5. Transmission
6. A running gear
7. A steering
8. Brake system
9. An electric equipment
10. A body
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 











4-10-proverka-i-ustanovka-faz-gazoraspredeleniya-po-metkam.html

4.10. Check and installation of phases timing on labels

It be required to you: a screw-driver, keys «on 8», «on 10», «on 13», a special key for проворачивания a cranked shaft.
1. Uncover heads of the block of cylinders («Replacement of a lining of a cover of a head of the block of cylinders» see).
2. Rotating a cranked shaft, combine labels on an asterisk of a camshaft and on the case of its bearings. If the chain is established correctly, the label on a pulley of a cranked shaft should coincide with a long label on a cover of a chain of a drive of a camshaft.
3. If labels do not coincide, unbend petals of a lock washer of a bolt of fastening of an asterisk of a camshaft.
4. Include the first transfer to fix a cranked shaft from проворачивания, turn away a bolt and...
5.... Remove it together with lock and persistent washers.

       THE PREVENTION
Lock and persistent washers are not fixed in any way on a bolt and it is easy from it act in film. Be cautious – do not drop them in the engine pallet.

6. Dismantle натяжитель chains (Replacement натяжителя chains of a drive of a camshaft »see«).

       THE NOTE
In the presence of necessary skills гидронатяжитель it is possible not to remove. To wring out плунжер гидронатяжителя the big screw-driver or an assembly shovel enough.

7. Remove an asterisk together with a chain, remove a chain from an asterisk and then again establish it on an asterisk, having changed chain position on asterisk teeths in the necessary party. It is recommended for to move once a chain on one tooth.
8. Put on an asterisk together with a chain a camshaft flange, having pulled a leading branch of a chain. As at change of position of a chain on an asterisk the aperture in an asterisk ceases to coincide with an adjusting pin in a flange, turn an a bit cranked shaft in the necessary party till the moment of coincidence of an aperture and a pin.
9. Establish a bolt of fastening of an asterisk together with persistent and lock washers and wrap it against the stop, without tightening definitively.
10. Having turned a cranked shaft on two turns, repeat check of position of labels as it did earlier.
11. If labels coincide, tighten a bolt and bend on a side of its head a petal of a lock washer. In case of discrepancy of labels repeat installation of phases timing.
12. Establish all removed before a detail in return sequence.

       GOOD ADVICE
In order to avoid an oil leak replace a lining of a cover of a head of the block of cylinders.

«The previous page
4.9. Installation of the piston of the fourth cylinder in position ВМТ of a step of compression
The following page»
4.11. Replacement натяжителя chains of a drive of a camshaft