Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
4.1. Features of a design
4.2. A good advice
4.3. Removal and installation of a decorative casing of the engine
4.4. Removal and installation of protection oil crankcase and an engine mudguard
4.5. Replacement of a cooling liquid
4.6. Oil replacement in the engine and the oil filter
4.7. Clearing of system of ventilation crankcase
4.8. Replacement of support of a suspension bracket of the power unit
4.9. Installation of the piston of the fourth cylinder in position ВМТ of a step of compression
4.10. Check and installation of phases timing on labels
4.11. Replacement натяжителя chains of a drive of a camshaft
4.12. Replacement успокоителя chains of a drive of a camshaft
4.13. Boot replacement натяжителя chains of a drive of a camshaft
4.14. Replacement of a chain of a drive of a camshaft
4.15. Replacement of hydrosupport of levers of a drive of valves
4.16. Removal, installation and дефектовка a flywheel
4.17. Replacement of the forward bearing of a primary shaft of a transmission
4.18. Replacement of details of consolidation of the engine
4.19. Camshaft replacement
4.20. A head of the block of cylinders
4.21. Removal and engine installation
4.22. Engine repair
4.23. Greasing system
4.24. Cooling system
4.25. System of release of the fulfilled gases
4.26. The power supply system
4.27. Possible malfunctions of the engine, their reason and ways of elimination
5. Transmission
6. A running gear
7. A steering
8. Brake system
9. An electric equipment
10. A body
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 















4-17-zamena-perednego-podshipnika-pervichnogo-vala-korobki-peredach.html

4.17. Replacement of the forward bearing of a primary shaft of a transmission

The forward bearing of a primary shaft of a transmission functionally concerns transmission and plays a role of a forward support of a shaft. But this bearing is located in a nest of a cranked shaft of the engine, therefore its replacement is described in the given section.
At deterioration or jamming of this bearing because of a greasing lack there is an effect of "conducting" coupling – the complicated gear change.
It be required to you: a special pusher of the bearing (at absence take advantage of make-shifts: greasing Litol-24 and sawdust), a hammer, a screw-driver.
On sale there is a considerable quantity of strippers for выпрессовки this bearing (inertial, цанговые, etc.). However not always they are had near at hand. The offered way with use of make-shifts in most cases leads to demanded result, as bearing landing in a nest of a cranked shaft rather weak.
1. Remove from the car a transmission and coupling (section 5 "Transmission" see).
2. Remove a flywheel (Removal, installation and дефектовка a flywheel see).
3. Prepare for выпрессовки the bearing a mix in a volume parity 1:1 from greasing Litol-24 and sawdust, having mixed them before reception of a homogeneous mix.

       THE NOTE
Mix volume – not less polyethylene cover from a 3-litre jar filled completely.

4. Fill with a mix an internal cavity behind the bearing.
5. Оправкой for a centering of a conducted disk выпрессовывайте the bearing, periodically adding a mix in process of a bearing exit...
6.... To its full exit from a nest.

       THE PREVENTION
After application of the specified method the bearing is not suitable to the further use and is subject to obligatory replacement.

7. Clear a nest of the bearing of a mix.
8. Through approaching on external diameter of the bearing the mandrel запрессуйте the bearing against the stop.

       THE PREVENTION
It is inadmissible запрессовывать the bearing, putting effort to an internal ring. In this case the bearing will be inevitably damaged.

9. Establish the removed details and knots in an order, the return to removal.


The previous page
4.16. Removal, installation and дефектовка a flywheel
The following page
4.18. Replacement of details of consolidation of the engine