Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
4.1. Features of a design
4.2. A good advice
4.3. Removal and installation of a decorative casing of the engine
4.4. Removal and installation of protection oil crankcase and an engine mudguard
4.5. Replacement of a cooling liquid
4.6. Oil replacement in the engine and the oil filter
4.7. Clearing of system of ventilation crankcase
4.8. Replacement of support of a suspension bracket of the power unit
4.9. Installation of the piston of the fourth cylinder in position ВМТ of a step of compression
4.10. Check and installation of phases timing on labels
4.11. Replacement натяжителя chains of a drive of a camshaft
4.12. Replacement успокоителя chains of a drive of a camshaft
4.13. Boot replacement натяжителя chains of a drive of a camshaft
4.14. Replacement of a chain of a drive of a camshaft
4.15. Replacement of hydrosupport of levers of a drive of valves
4.16. Removal, installation and дефектовка a flywheel
4.17. Replacement of the forward bearing of a primary shaft of a transmission
4.18. Replacement of details of consolidation of the engine
4.19. Camshaft replacement
4.20. A head of the block of cylinders
4.21. Removal and engine installation
4.22. Engine repair
4.23. Greasing system
4.24. Cooling system
4.25. System of release of the fulfilled gases
4.26. The power supply system
4.27. Possible malfunctions of the engine, their reason and ways of elimination
5. Transmission
6. A running gear
7. A steering
8. Brake system
9. An electric equipment
10. A body
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 















4-14-zamena-cepi-privoda-raspredelitelnogo-vala.html

4.14. Replacement of a chain of a drive of a camshaft

If at serviceable натяжителе and its boot, and also at not worn out asterisks of a drive it is not possible to restore a chain tension, means, the chain was excessively extended also it it is necessary to replace.
It be required to you: keys «on 10», «on 13», «on 17», a special key for a nut of fastening of a pulley of a cranked shaft, a screw-driver, an assembly shovel, a hammer, small beards.
1. Uncover heads of the block of cylinders («Replacement of a lining of a cover of a head of the block of cylinders» see).
2. Remove a boot натяжителя chains of a drive of a camshaft (boot Replacement натяжителя chains of a drive of a camshaft »see«).
3. Remove a chain from asterisks of a cranked shaft, a shaft of a drive of the oil pump...
4.... A camshaft also take out a chain from a cavity of a drive of a camshaft upwards.

       THE PREVENTION
After chain removal if it removed only for replacement, do not turn cranked and distributive shaft in order to avoid displacement of phases timing.

5. Oil a new chain before installation for the engine.
6. Enter a new chain from above into a cavity of a drive of a camshaft, lower it downwards and put on asterisks of a cranked shaft and a shaft of a drive of the oil pump, having provided a tension of a branch of a chain between asterisks.
7. Put on a chain a camshaft asterisk, having provided a tension of a branch of a chain between it and an asterisk of a shaft of a drive of the oil pump.
8. Wrap a bolt of fastening of an asterisk of a camshaft, without tightening it.
9. Establish a boot натяжителя chains in an order, the return to removal.
10. Establish натяжитель in an order, the return to removal.
11. Switch off transfer, turn a cranked shaft on 2–3 turns in a rotation direction.
12. Be convinced of simultaneous coincidence of labels on asterisks with labels on the engine (Check and installation of phases timing on labels »see«). If labels do not coincide, repeat chain installation.
13. If labels coincide, include transfer, tighten a bolt of an asterisk of a camshaft and Tighten the it.
14. Establish the removed details in an order, the return to removal.

«The previous page
4.13. Boot replacement натяжителя chains of a drive of a camshaft
The following page»
4.15. Replacement of hydrosupport of levers of a drive of valves