Chevrolet-Niva
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. The engine
4.1. Features of a design
4.2. A good advice
4.3. Removal and installation of a decorative casing of the engine
4.4. Removal and installation of protection oil crankcase and an engine mudguard
4.5. Replacement of a cooling liquid
4.6. Oil replacement in the engine and the oil filter
4.7. Clearing of system of ventilation crankcase
4.8. Replacement of support of a suspension bracket of the power unit
4.9. Installation of the piston of the fourth cylinder in position ВМТ of a step of compression
4.10. Check and installation of phases timing on labels
4.11. Replacement натяжителя chains of a drive of a camshaft
4.12. Replacement успокоителя chains of a drive of a camshaft
4.13. Boot replacement натяжителя chains of a drive of a camshaft
4.14. Replacement of a chain of a drive of a camshaft
4.15. Replacement of hydrosupport of levers of a drive of valves
4.16. Removal, installation and дефектовка a flywheel
4.17. Replacement of the forward bearing of a primary shaft of a transmission
4.18. Replacement of details of consolidation of the engine
4.19. Camshaft replacement
4.20. A head of the block of cylinders
4.21. Removal and engine installation
4.22. Engine repair
4.23. Greasing system
4.24. Cooling system
4.25. System of release of the fulfilled gases
4.26. The power supply system
4.27. Possible malfunctions of the engine, their reason and ways of elimination
5. Transmission
6. A running gear
7. A steering
8. Brake system
9. An electric equipment
10. A body
11. Variants of execution of the car
12. Care of the car
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Appendices
 















4-8-zamena-opor-podveski-silovogo-agregata.html

4.8. Replacement of support of a suspension bracket of the power unit

The power unit is established on two rubber pillows from both parties of the engine and one support (too rubber) under the extension piece crankcase transmissions.
It be required to you: keys «on 13», on «17» (head), a jack or the similar load-lifting mechanism.
1. Will hang out a forward part of the car on support or lift the car on the lift.
2. Remove protection oil crankcase and a mudguard of a motor compartment (Removal and installation of protection oil crankcase and an engine mudguard »see«).
3. Disconnect, having turned out a fastening bolt, from an arm of the right support of the engine распорку a receiver of an inlet pipe as it disturbs to the further work.
4. Turn away a nut of fastening of a pillow of the right support to an arm of the engine and...
5.... To a cross-beam of a forward suspension bracket.
6. Similarly disconnect top and...
7.... Bottom fastenings of a pillow of the right support.
8. A jack raise the engine so...
9.... That pillows were released also them it would be possible to take out.

       GOOD ADVICE
In the absence of a jack enclose under the pallet of the engine of a board (or one more support) and lower the car a little.

10. Establish new pillows in an order, the return to removal.
11. For replacement of a pillow of a back support of the power unit turn on two nuts of fastening of a pillow to картеру transmissions...
12.... And two nuts of fastening of a cross-beam of a back support to the body basis.

       THE PREVENTION
At отворачивании nuts of fastening of a cross-beam substitute under картер transmissions a suitable support.

13. Turn away a nut of bolts of fastening of a pillow to a cross-beam of a back support and take out bolts.
14. Having hooked a screw-driver, take out распорные plugs and...
15.... Remove a pillow.
16. In need of replacement remove a cross-beam of a back support.
17. Establish a cross-beam and a pillow of a back support in an order, the return to removal.

«The previous page
4.7. Clearing of system of ventilation crankcase
The following page»
4.9. Installation of the piston of the fourth cylinder in position ВМТ of a step of compression